By Tutorial for Bathtub Installation
By Tutorial for Bathtub Installation
Blog Article
The article author is making a few great points related to A Step-by-Step Guide to Installing a Bathtub overall in this article below.
Installing a tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately difficult job. If the old bathtub is readily easily accessible, the job can move speedily; if you have to open a wall to get rid of the old bathtub and position the brand-new tub, the job is much harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub as well as embeded in the new one. See to it you have certified on your own for the job as well as fit trying it. Rather than employing a service provider to take over a halfway-completed task, it is far better to take into consideration using one before you begin. Chances are you may require a professional plumber to make tube links.
This post will help you mount a new bath tub in your washroom if you have already purchased a brand-new tub and do not require to alter the setup of your previous water pipes.
Your tools and material checklist should consist of the following:
Getting ready for the Setup
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to avoid pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing faucets can be quite bothersome because of the limited gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, put the bathtub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bathtub up until the level checks out degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the proper supply pipeline by making a compression join; after that do the same for the other tap.
Switch on the water as well as check all joints and brand-new pipework for leaks as well as tighten them if required. Load the tub as well as also check the overflow electrical outlet as well as the typical electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub must wait till the bath tub has been made use of a minimum of once as this will settle it into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in place between the tap and the sink. Protect the tap in place with the manufacturer supplied backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, bring about issues with wetness and also possible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is advisable to fit the floor tiles using water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on A Step-by-Step Guide to Installing a Bathtub? Give a short review down below. We'd be interested to find out your insights about this posting. We are looking forward that you come back again soon. In case you enjoyed our blog post please don't forget to share it. Bless you for your time. Please come visit our site back soon.
Quote & Schedule Report this page